This guide will demonstrate how-to crack Mikrotik ver 3.30

STEPS INVOLVED

# First install Mikrotik 3.20
# Add Ip Address for remote login
# Download KEYGEN
# Upload keygen.npk into Mikrotik FILES section via winbox & Reboot *** Must do, otherwise SSH will give connection refused error.
# SSH to Mikrotik and run the keygen
# Import the KEY
# Download Mikrotik 3.30 Version and upload it to FILES Section & Shutdown.
# DONE. Check Mikrotik version , it should be 3.30 with L6

Let’s begin . . .
# MIKROTIK 3.20 INSTALLATION

1) First install Mikrotik 3.20 from
1    http://204.62.56.64/mikrotik/3.20/mikrotik-3.20.iso



Remember to un-check the following components.

mpls-test
routing-test
wireless-test
xen

As shown in the image below.



Then Press ‘i’ to start installation.
After installation complete, press ENTER to reboot.

After booting, Login to console.
First time default id of fresh installation of Mikrotik is
ID = admin
Pass = no password, just Enter
# ADD IP ADDRESS FOR REMOTE LOGIN SUPPORT

Now add an IP Address so we can remotely login to Mikrotik via sshin later steps.Use the following command
1    /ip address add address=192.168.2.1/24 interface=ether1


As shown in the image below.



Note: As you can see ROUTER HAS NO SOFTWARE KEY and you have 24 hours limit to enter a valid key.
Now its time to break this up.
# DOWNLOAD KEYGEN

Download Keygen from
1    http://www.4shared.com/rar/9VLogU-q/Syed-Jahanzaib-MT-330_Full.html



OR
1    http://megaupload.com/?d=HNOGD4YM


[if the above link don't work, email me at aacable [at] hotmail.com
and i will send you the keygen in .rar format.

Unzip it any folder for example c:\keygen
You will see following contents.


Upload keygen.npk into Mikrotik FILES section

Now connect to Mikrotik via WINBOX and upload keygen.npk (from c:\keygen) into FILES section.
As shown in the image below.



.

# Now restart Mikrotik and it will automatically install keygen.npk in mikrotik system.

Upon Rebooting you should see the INSTALLING KEY GEN on the console window, This is must, otherwise you will get ‘connection refused error’.


.

After Rebooting, Make sure you get the keygen package file in System/Packages List.
As showed in the image below . . .

SSH TO EXECUTE KEYGEN

After booting. from your PC, Open command prompt , goto the folder where you extracted the keygen file i.e c:\keygen
1    cd c:\keygen



Now Connect with ssh to mikrotik via following command (ssh is included in this folder)
1    ssh 192.168.2.1


& Type the following command
1    roskey /dev/hda HU6I-XPT



As shown in the image below.



NOTE: Various harddisk have different code as below (Adjust it according to your harddisk chemistry)
hda= HD Virtual
hdb= HD IDE
sda= HD sata

It will take Long time, this is the only irritating & time taken section of the whole process (Mine took about 3 hours, your’s can be less depend on the hardware) to change the KEY on Mikrotik to match our’s, So sit back , Relax and have a cup of TEA)
After completing the process, it will show you the message “WORK FINE“.
As shown in the image below.



Now Shutdown the Mikrotik PC. Now start it again and Verify that your mikrotik key have changed to HU6I-XPT.
IMPORT LICENSE KEY IN 3.20

Goto SYSTEM / LICENSE and click IMPORT License and point it to the key at c:\keygen\HU6I-XPT.key
As shown in the image below.



It will ask you to Reboot. Do it 

After rebooting, Goto SYSTEM/LICENSE and see your New Key in Action
Now that we have cracked Mikrotik 3.20, its time to upgrade it to 3.30 which supports PCC.
FINALLY UPGRADE TO VER 3.30   

Download Mikrotik 3.30 version (.NPK Update Package File) from
1    http://204.62.56.64/mikrotik/3.30/routeros-x86-3.30.npk


Upload this file to mikrotik FILES section (by copy paste or drag n drop method) & Reboot, it will automatically update the base Ver to 3.30



After rebooting , check License Level and Mikrotik version.